Sub-slab depressurization
Sub-slab depressurization costs $1,200–$2,000 installed (HomeGuide, 2026) and cuts radon 50 to 99% in EPA's table. How it works and what moves the price.
- $1,200–$2,000 typical installed system (HomeGuide)
- 4 pCi/L is EPA's action level
- 1 in 15 US homes estimated elevated (EPA)
- Free quotes from certified or licensed mitigators
Fast response from independent local providers. No obligation.
Typical national cost$1,200 – $2,000Cost guide →About Sub-slab depressurization
Active sub-slab suction is the method most homes end up with. EPA's Consumer's Guide calls it "the most common and usually the most reliable radon reduction method," and its cost table credits it with a 50 to 99 percent reduction. A contractor drills one or more holes through the floor slab, sets a pipe into the gravel or soil underneath, and runs it to a fan that exhausts above the roofline. The fan keeps the space under the slab at lower pressure than the house, so soil gas is pulled out before it can seep in.
HomeGuide's February 2026 survey puts a typical system at $1,200 to $2,000 installed, with a national average of $1,600 and $2,500 or more for large homes. EPA's 2010 figure for the same work was $800 to $2,500, in 2010 dollars. EPA notes that often only a single suction point is needed; how many depends on how easily air moves through the material under the slab, which a contractor can check with a soil communication test (a vacuum in one hole, smoke at another).
Common Jobs We Route
- Active sub-slab suction for a basement or slab home: $1,200–$2,000 installed (HomeGuide, Feb 2026), $2,500+ for large homes
- Sump-hole suction: the sump capped with an airtight lid so it still drains and doubles as the suction point ($900–$2,500 for sump sealing, HomeGuide)
- Adding a fan to an existing passive pipe in a newer home: about $300 (EPA 2010 guide, 2010 dollars)
- Sealing the sump and major cracks as part of the system, which EPA says makes suction work better
- Post-mitigation test: $125–$400 professional or $10–$30 for a kit (HomeGuide)
What Affects the Price
Providers quote their own work — these are the factors that consistently move the number.
- Number of suction points: EPA says it depends on how easily air moves under the slab (extra points est. $250–$500 each in our calculator)
- Pipe route: an exterior wall is usually simpler than threading pipe through closets to the attic (interior or attic route est. ×1.15)
- How much sealing the slab needs
- Home footprint (2,500 sq ft or more, est. ×1.25) and a mixed foundation, such as a basement plus a crawlspace or slab addition (est. ×1.5)
- Permit $25–$150 where required, usually included in the bid (HomeGuide)
- Running cost after install: fan electricity and heated or cooled air loss, $50–$200 a year (EPA, 2010 dollars)
How It Works
- Step 1
Confirm the result
EPA recommends fixing a home when one long-term test, or the average of two short-term tests, reads 4 pCi/L or more, and considering a fix between 2 and 4 pCi/L.
- Step 2
Get two itemized bids
Ask each credentialed mitigator for the system type, suction points, fan model and warranty, pipe route, sealing scope, permit and a post-mitigation test, and compare each bid with the calculator range.
- Step 3
Retest after installation
EPA recommends a 2- to 7-day test within 30 days of installation but no sooner than 24 hours after the fan starts, then retesting at least every two years.
Free Sub-slab depressurization Tools
Get a realistic number or a quick diagnosis first — free, built on published industry data.
Cost Guides
Sub-slab depressurization FAQs
How much does sub-slab depressurization cost?
$1,200 to $2,000 installed for a typical system, national average $1,600 (HomeGuide, Feb 2026). EPA's 2010 guide gave $800 to $2,500 in 2010 dollars.
Is a passive system enough?
Usually not on its own. EPA's table gives passive sub-slab suction a 30 to 70 percent reduction against 50 to 99 percent for active suction, and says a fan can be added to an existing passive pipe for about $300 (2010 dollars).
Where does the fan go?
EPA says the fan should sit outside or in an unoccupied attic, never in or below a living area, and must run continuously for the system to work.
Sub-slab depressurization by Area
Need sub-slab depressurization?
Send the short form — no obligation.